第一次编译的固件，失败！
Boot and Recovery Environment for Embedded Devices Copyright (C) 2018 HackPascal <hackpascal@gmail.com> Build date 2018-03-23 [git-994feec] Version 1.1 (r1211) DRAM: 32MB Platform: Qualcomm Atheros QCA953X rev 2 Board: Generic board Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash: Macronix MX25L6435E (8MB) on ath79-spi ag71xx-eth: MAC address is invalid, using default settings. ag71xx-eth: Using MAC address 00:13:74:00:00:01 Waiting for auto-negotiation complete ... OK eth0: Atheros AR8228/AR8229 rev 1 Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0 Press any key to interrupt autoboot ... 2 Autoboot aborted due to button press. Starting breed built-in shell breed> breed> breed> breed> boot Usage: boot mem <addr> - Boot from memory address or memory-mapped address boot flash [bank <n>] <addr> - Boot from flash boot linux <addr> - Boot linux kernel at <addr> boot raw <addr> - Disable interrupts and jump to <addr> boot breed <addr> - Boot given breed file at <addr> breed> boot flash Usage: boot mem <addr> - Boot from memory address or memory-mapped address boot flash [bank <n>] <addr> - Boot from flash boot linux <addr> - Boot linux kernel at <addr> boot raw <addr> - Disable interrupts and jump to <addr> boot breed <addr> - Boot given breed file at <addr> breed> reboot Unrecognised command: reboot Type 'help' to get available commands. breed> ps Unrecognised command: ps Type 'help' to get available commands. breed> help Available commands: about - About this bootloader abstatus - Interrupt status of autoboot arp - Display ARP table autoboot - Detect firmware type and boot automatically boot - Boot firmware btntst - Test GPIO of buttons dhcp - Display DHCP leases env - Environment variables utility envconf - Configure environment variable block exit - Exit from telnet flash - Flash utility gpio - GPIO utilities help - Show available commands mdio - MDIO utility mem - Memory operation utilities net - Network control netstat - Display network state reset - Restart device setbrg - Set baudrate spi - SPI utility sysinfo - Display system information thread - Display all threads wget - Retrieval file through HTTP breed> autoboot Trying to boot firmware from 0x9f680000 ... U-Boot firmware image header detected. Image Name: MIPS OpenWrt Linux-3.3.8 Data Size: 1026203 Bytes Load Address: 80060000 Entry Point: 80060000 Uncompressing data (LZMA) ... done. Flushing cache ... done. Starting kernel at 0x80060000... [ 0.000000] Linux version 3.3.8 (hades@hades) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed May 16 16:16:25 CST 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=AP143 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art),7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00037fd0 [ 0.000000] Readback ErrCtl register=00037fd0 [ 0.000000] Memory: 28936k/32768k available (2169k kernel code, 3832k reserved, 563k data, 176k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:83 [ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] Initialized recycle list for cpu 0. [ 0.070000] NET: Registered protocol family 16 [ 0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79 [ 0.080000] MIPS: machine is Qualcomm Atheros AP143 reference board [ 0.090000] ar71xx: invalid MDIO id 1 [ 0.500000] bio: create slab <bio-0> at 0 [ 0.510000] Switching to clocksource MIPS [ 0.520000] NET: Registered protocol family 2 [ 0.520000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.520000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.530000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.530000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.540000] TCP reno registered [ 0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.560000] NET: Registered protocol family 1 [ 0.580000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.580000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.590000] msgmni has been set to 56 [ 0.600000] io scheduler noop registered [ 0.600000] io scheduler deadline registered (default) [ 0.610000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.640000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.640000] console [ttyS0] enabled, bootconsole disabled [ 0.640000] console [ttyS0] enabled, bootconsole disabled [ 0.660000] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.660000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.670000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.670000] Creating 6 MTD partitions on "spi0.0": [ 0.680000] 0x000000000000-0x000000040000 : "u-boot" [ 0.690000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.690000] 0x000000050000-0x000000680000 : "rootfs" [ 0.700000] mtd: partition "rootfs" set to be root filesystem [ 0.710000] mtd: partition "rootfs_data" created automatically, ofs=60000, len=620000 [ 0.710000] 0x000000060000-0x000000680000 : "rootfs_data" [ 0.720000] 0x000000680000-0x0000007f0000 : "kernel" [ 0.730000] 0x0000007f0000-0x000000800000 : "art" [ 0.730000] 0x000000050000-0x0000007e0000 : "firmware" [ 0.770000] ag71xx_mdio: probed [ 0.900000] ag71xx_mdio: probed [ 0.910000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 1.480000] eth1: Atheros AG71xx at 0xba000000, irq 5 [ 2.030000] eth1: Found an AR934X built-in switch [ 3.070000] TCP cubic registered [ 3.070000] NET: Registered protocol family 17 [ 3.080000] 8021q: 802.1Q VLAN Support v1.8 [ 3.080000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 3.090000] Freeing unused kernel memory: 176k freed [ 3.100000] Kernel panic - not syncing: No init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.qsdk 修改后再次编译，
Boot and Recovery Environment for Embedded Devices Copyright (C) 2018 HackPascal <hackpascal@gmail.com> Build date 2018-03-23 [git-994feec] Version 1.1 (r1211) DRAM: 32MB Platform: Qualcomm Atheros QCA953X rev 2 Board: Generic board Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash: Macronix MX25L6435E (8MB) on ath79-spi ag71xx-eth: MAC address is invalid, using default settings. ag71xx-eth: Using MAC address 00:13:74:00:00:01 Waiting for auto-negotiation complete ... OK eth0: Atheros AR8228/AR8229 rev 1 Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0 Press any key to interrupt autoboot ... 2 Autoboot aborted due to button press. Starting breed built-in shell breed> Upgrade completed. Rebooting in 2 seconds ... Resetting ... Boot and Recovery Environment for Embedded Devices Copyright (C) 2018 HackPascal <hackpascal@gmail.com> Build date 2018-03-23 [git-994feec] Version 1.1 (r1211) DRAM: 32MB Platform: Qualcomm Atheros QCA953X rev 2 Board: Generic board Clocks: CPU: 550MHz, DDR: 400MHz, AHB: 200MHz, Ref: 25MHz Flash: Macronix MX25L6435E (8MB) on ath79-spi ag71xx-eth: MAC address is invalid, using default settings. ag71xx-eth: Using MAC address 00:13:74:00:00:01 Waiting for auto-negotiation complete ... OK eth0: Atheros AR8228/AR8229 rev 1 Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0 Press any key to interrupt autoboot ... 2 Autoboot aborted due to button press. Starting breed built-in shell breed> autoboot Trying to boot firmware from 0x9f680000 ... U-Boot firmware image header detected. Image Name: MIPS OpenWrt Linux-3.3.8 Data Size: 954963 Bytes Load Address: 80060000 Entry Point: 80060000 Uncompressing data (LZMA) ... done. Flushing cache ... done. Starting kernel at 0x80060000... [ 0.000000] Linux version 3.3.8 (hades@hades) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r40331) ) #1 Fri May 18 10:33:12 CST 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 rev 2 [ 0.000000] Clocks: CPU:550.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=AP143 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6336k(rootfs),1472k(kernel),64k(art),7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00017fd0 [ 0.000000] Readback ErrCtl register=00017fd0 [ 0.000000] Memory: 28992k/32768k available (2191k kernel code, 3776k reserved, 437k data, 220k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:83 [ 0.000000] Calibrating delay loop... 366.18 BogoMIPS (lpj=1830912) [ 0.060000] pid_max: default: 32768 minimum: 301 [ 0.060000] Mount-cache hash table entries: 512 [ 0.070000] Initialized recycle list for cpu 0. [ 0.070000] NET: Registered protocol family 16 [ 0.080000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79 [ 0.090000] MIPS: machine is Qualcomm Atheros AP143 reference board [ 0.100000] ar71xx: invalid MDIO id 1 [ 0.510000] bio: create slab <bio-0> at 0 [ 0.520000] Switching to clocksource MIPS [ 0.530000] NET: Registered protocol family 2 [ 0.530000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.530000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.540000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.540000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.550000] TCP reno registered [ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.570000] NET: Registered protocol family 1 [ 0.590000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.590000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.600000] msgmni has been set to 56 [ 0.610000] io scheduler noop registered [ 0.610000] io scheduler deadline registered (default) [ 0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.650000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.650000] console [ttyS0] enabled, bootconsole disabled [ 0.650000] console [ttyS0] enabled, bootconsole disabled [ 0.670000] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.670000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.680000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.690000] Creating 6 MTD partitions on "spi0.0": [ 0.690000] 0x000000000000-0x000000040000 : "u-boot" [ 0.700000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.700000] 0x000000050000-0x000000680000 : "rootfs" [ 0.710000] mtd: partition "rootfs" set to be root filesystem [ 0.720000] mtd: partition "rootfs_data" created automatically, ofs=260000, len=420000 [ 0.730000] 0x000000260000-0x000000680000 : "rootfs_data" [ 0.730000] 0x000000680000-0x0000007f0000 : "kernel" [ 0.740000] 0x0000007f0000-0x000000800000 : "art" [ 0.750000] 0x000000050000-0x0000007e0000 : "firmware" [ 0.780000] ag71xx_mdio: probed [ 0.910000] ag71xx_mdio: probed [ 0.920000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.480000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 1.490000] eth1: Atheros AG71xx at 0xba000000, irq 5 [ 2.050000] eth1: Found an AR934X built-in switch [ 3.080000] TCP cubic registered [ 3.080000] NET: Registered protocol family 17 [ 3.090000] 8021q: 802.1Q VLAN Support v1.8 [ 3.090000] ### of_selftest(): No testcase data in device tree; not running tests [ 3.100000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 3.110000] Freeing unused kernel memory: 220k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - jffs2 not ready yet; using ramdisk - init - [ 9.850000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 [ 9.850000] Backport generated by backports.git backports-20130617-4-ge3220f5 [ 9.890000] cfg80211: Calling CRDA to update world regulatory domain [ 9.890000] cfg80211: World regulatory domain updated: [ 9.900000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 9.910000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.920000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.920000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.930000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 9.940000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 9.950000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 10.180000] SCSI subsystem initialized [ 10.330000] usbcore: registered new interface driver usbfs [ 10.330000] usbcore: registered new interface driver hub [ 10.340000] usbcore: registered new device driver usb [ 10.950000] Button Hotplug driver version 0.4.1 [ 11.050000] PPP generic driver version 2.4.2 [ 11.150000] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 11.270000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.370000] NET: Registered protocol family 24 [ 11.400000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.400000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller [ 11.410000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 11.450000] ehci-platform ehci-platform.0: irq 3, io mem 0x1b000000 [ 11.470000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 11.470000] hub 1-0:1.0: USB hub found [ 11.480000] hub 1-0:1.0: 1 port detected [ 11.500000] nf_conntrack version 0.5.0 (456 buckets, 1824 max) [ 11.770000] Initializing USB Mass Storage driver... [ 11.780000] usbcore: registered new interface driver usb-storage [ 11.780000] USB Mass Storage support registered. Please press Enter to activate this console. BusyBox v1.19.4 (2018-05-17 18:29:38 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. MM NM MMMMMMM M M $MMMMM MMMMM MMMMMMMMMMM MMM MMM MMMMMMMM MM MMMMM. MMMMM:MMMMMM: MMMM MMMMM MMMM= MMMMMM MMM MMMM MMMMM MMMM MMMMMM MMMM MMMMM' MMMM= MMMMM MMMM MM MMMMM MMMM MMMM MMMMNMMMMM MMMM= MMMM MMMMM MMMMM MMMM MMMM MMMMMMMM MMMM= MMMM MMMMMM MMMMM MMMM MMMM MMMMMMMMM MMMM= MMMM MMMMM, NMMMMMMMM MMMM MMMM MMMMMMMMMMM MMMM= MMMM MMMMMM MMMMMMMM MMMM MMMM MMMM MMMMMM MMMM= MMMM MM MMMM MMMM MMMM MMMM MMMM MMMM MMMM$ ,MMMMM MMMMM MMMM MMM MMMM MMMMM MMMM MMMM MMMMMMM: MMMMMMM M MMMMMMMMMMMM MMMMMMM MMMMMMM MMMMMM MMMMN M MMMMMMMMM MMMM MMMM MMMM M MMMMMMM M M M --------------------------------------------------------------- For those about to rock... (Attitude Adjustment, r40331) --------------------------------------------------------------- root@OpenWrt:/# [ 17.080000] device eth1 entered promiscuous mode [ 17.680000] eth1: link up (1000Mbps/Full duplex) [ 17.680000] br-lan: port 1(eth1) entered forwarding state [ 17.690000] br-lan: port 1(eth1) entered forwarding state [ 19.690000] br-lan: port 1(eth1) entered forwarding state root@OpenWrt:/# [ 31.740000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 31.740000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 31.750000] jffs2_build_filesystem(): erasing all blocks after the end marker...